![]() ![]() The hour display will flash and can be changed using the "MODE" button, more quickly if you hold the button down. If Tm is displayed, press the MODE button for 2 seconds to display the clock time. The calibration number will flicker.Ĭycle through the modes until Tm or the clock is displayed. Use "START/STOP" (front) button to put into "stop" state (mile/h symbol not flashing.) Use "MODE" (top) button to get to "ODO" mode. Settings may be changed in these modes as described below. Pressing the "MODE" button will cycle the computer through the modes: When calibration value "A" is set to desired number, press "SET" (underside) button to accept and put the computer into normal operation. Use "MODE" (top) button to raise calibration number, or "START/STOP" (front) button to decrease it. When total miles/km value is set to desired number, press "SET" (underside) button to accept and enter wheel calibration mode. ![]() Press "MODE" (top) button to adjust that digit. Use "START/STOP" (front) button to change which digit is flashing. Press "MODE" (top) button for two seconds to enter "odometer setting" (total km/miles) mode. Press "MODE" (top) button to select "mph" (miles) or "km/h" (kilometers). Push all three buttons at once ("SET" button is on underside of unit.) Do this to clear the computer's memory after replacing the battery: If these buttons are further held down for more than 3 seconds, the wheel calibration value moves between "A" and "B" values.įor total reset. When the "START/STOP" (left) and "MODE" (right) button are pressed together in "ODO" mode, first the wheel calibration number appears. To select which weel calibration value to use: Press and hold the "SET" button for 2 seconds to switch back and forth between "A" and "B" calibration value. Press the "SET" button with a ballpont pen or similar tool. Use "START/STOP" button to put into "stop" state (mile/h symbol not flashing.) To revise wheel size without losing mileage: If you hold the "SET" button for 2 seconds or more, you enter the mode to set the alternate ("B") calibration number. When calibration value "A" is set to desired number, press "SET" (recessed) button to accept. Note: This unit permits the entry of two different calibration numbers ("A" & "B") to allow the same computer to be used with different bicycles Use "MODE" (right) button to raise calibration number, or "START/STOP" (left) button to decrease it. When odometer value is set to desired number, press "SET" (recessed) button to accept and enter wheel calibration mode. Press "MODE" (right) button to adjust next digit. Use "START/STOP" (left) button to change flashing digit. Press "MODE" (right) button to enter "odometer setting" mode. Use "START/STOP" (left) button to select "M" (miles) or "Km" (kilometers). Press "MODE" (right) button to enter distance scale selection mode. Push all three buttons at once ("SET" button is recessed on bottom of unit.) If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.If you make a note of the odometer reading before changing batteries, you can re-enter the total distance reading after installing the new battery. Our support team searches for useful product information and answers to frequently asked questions. Cateye CC-VT245W Urban Cycling Computer.Cateye CC-VT240W Urban Cycling Computer.Cateye CC-VT220W Urban Cycling Computer.Cateye CC-VT100W Vectra Cycling Computer.Cateye CC-VL810 Velo 8 Cycling Computer.Cateye CC-VL510 Velo 5 Cycling Computer.Cateye CC-SC100B Padrone Smart Cycling Computer.Cateye CC-RD310W Strada Slim Cycling Computer.Cateye CC-RD300W Strada Cycling Computer.Cateye CC-RD100N Strada Cycling Computer.Cateye CC-PA500B Padrone Smart Cycling Computer.Cateye CC-MC100W Micro Cycling Computer. ![]()
0 Comments
Leave a Reply. |